DigiRail IoT Gateway With Ethernet
This economical module solves the problem of data collection in local or remote applications. DigiRail IoT helps assimilate sensors and RS485 devices using existing network infrastructure to provide data acquisition and logging — hardwired remote I/O to MQTT or Modbus, passing data to OEE, DCS, or SCADA, with open MQTT broker compatibility and gateway functions for both Modbus TCP-to-RTU and Modbus RTU-to-MQTT, plus an RS485 Master mode with 8 channels/registers.
Direct connection of sensors and analogue signals is supported. The module contains 6 digital inputs, individually configurable to monitor state (On/Off) or act as counters, plus two analogue inputs and two digital outputs.
Initial configuration in Novus NXperience is an extremely quick process. With a small amount of interface wiring the module can begin gathering data in minutes. This can be passed via MQTT to Cloud services, or sent to PLC/SCADA systems using the Modbus TCP protocol.
Modbus TCP to RTU Pass-Through Gateway
This model can be used as a transparent gateway with no mapping of registers required. It's suitable for reading/writing registers on RTU Slaves wired to the RS485 terminals — simply communicate via Modbus TCP and the module automatically translates commands.
Gateway Mode is a simple method allowing IT equipment or PLCs with Ethernet ports to communicate with devices such as temperature controllers, instruments, and meters — removing the physical mismatch between Ethernet/LAN cabling and RS485, and compensating for differences in protocol message structure.
Modbus RS485 Master Mode
When configured as an RS485 Master, the IoT Gateway can receive up to 8 registers via the built-in RS485 terminals — useful for collecting data from field devices such as metering equipment equipped with RS485 terminals. The 8 registers can be received from a single device or multiple devices with different addresses. Unlike basic gateway mode, register values are held in the device's internal memory.
✅ 3 Year Manufacturer Warranty — backed by our UK-based technical support
Novus DigiRail IoT Ethernet Datasheet Download
Novus DigiRail IoT Ethernet Manual Download
Technical Details
Inputs: 6 digital, 2 analog. Outputs: 2 digital
Analog input types: 0-5V, 0-10V, 0-20mA, 4-20mA. Digital input types: NPN, PNP, dry contact
Analog input impedance: mA 15Ω+1.5V, V 1MΩ
Digital input: Logic "0" <0.5V, Logic "1" >3V, max voltage 30V, input impedance 270kΩ, input current @30VDC typical 0.15mA
Max frequency: dry contact 10Hz, PNP/NPN 3kHz. Min pulse duration: dry contact 50ms, PNP/NPN 150μs
Digital outputs: 2 NPN-type, max switchable current 700mA
Analog inputs: 15 bits (32,000 levels)
Communication: USB, Ethernet 10/100 Mb/s (IEEE 802.3u), RS485. Software: NXperience
Power supply: 10-30VDC. Consumption: 50mA @24V, 120mA @12V
Operating conditions: -20 to 60°C, 5-95% RH non-condensing
Battery: CR2032 for internal clock retention. Mounting: DIN rail or screw. Protection: IP20. Enclosure: ABS+PC
Frequently Asked Questions
Can this connect existing RS485 devices to an Ethernet network?
Yes — as a transparent Modbus TCP to RTU gateway, it lets Ethernet-equipped PLCs communicate with RS485-only field devices with no register mapping required.
Can it collect data without a full Modbus network?
Yes — in RS485 Master mode it reads up to 8 registers directly from one or more field devices, holding the values in its own internal memory.
Is there a WiFi version?
Yes — see our DigiRail IoT WiFi model if you need wireless rather than wired Ethernet connectivity.
Industry Applications
- Remote Data Collection — gathers sensor and RS485 device data over existing network infrastructure.
- OEE & Machine Monitoring — passes hardwired I/O data to OEE, DCS, or SCADA systems.
- Legacy Device Integration — bridges RS485-only field devices onto an Ethernet/Modbus TCP network.